Specifications1)
| Model |
APL2201-P90 |
APL2203-P90 |
APL2205-P90 |
| Output energy |
| at 1064 nm |
10 mJ |
30 mJ |
60 mJ |
| at 532 nm2) |
5 mJ |
15 mJ |
30 mJ |
| at 355 nm3) |
3 mJ |
10 mJ |
20 mJ |
| at 266 nm4) |
1 mJ |
2.5 mJ |
4 mJ |
| Pulse energy stability (Std.Dev.)5) |
| at 1064 nm |
1 % |
| at 532 nm |
1.5 % |
| at 355 nm |
2 % |
| at 266 nm |
4 % |
| Pulse duration (FWHM)6) |
90±10 ps |
| Pulse duration stability7) |
±3 ps |
| Pulse repetition rate8) |
1000 Hz |
| Triggering mode |
external |
| Spatial mode9) |
super-Gaussian |
| Beam divergence10) |
<1 mrad |
<0.7 mrad |
| Typical beam diameter11) |
~3 mm |
~5 mm |
~6 mm |
| Beam pointing stability12) |
<60 µrad |
| Pre-pulse contrast |
>50:1 |
| Polarization |
Linear, >95 % |
| Physical characteristics |
| Laser head size (WxHxL) |
455x242x1035 mm |
900x350x1500 mm |
1200x350x2200 mm |
| Power supply size (WxHxL) |
550x680x600 mm |
550x860x600 mm |
550x1030x600 mm |
| Chiller size (WxHxL) |
400x790x430 mm |
400x790x430 mm |
500x850x500 mm |
| Operating requirements |
| Water service |
Not required, air-cooled |
| Relative humidity (non condensing) |
20-80 % |
| Operating ambient temperature |
22±2°C |
| Mains voltage |
208 or 230 V AC, single phase, 50/60 Hz |
| Power rating13) |
<1.0kVA |
<2.5kVA |
<5kVA |
1) All specifications are subject to change without notice. The parameters marked typical are not specifications. They are indications of typical performance and will vary with each unit we manufacture. Unless stated otherwise all specifications are measured at 1064 nm. All specifications measured when PL2210B laser as seed laser was used.
2) For APL220x-SH and APL220x-SH/FH options. Outputs are not simultaneous.
3) For APL220x-TH option. Outputs are not simultaneous.
4) For APL220x-SH/FH option. Outputs are not simultaneous.
5) Averaged from 300 pulses at 1 kHz pulse repetition rate.
6) Depends on seed laser. Optional 30 ps duration, in this case PL2210A laser as seed laser should be used. Inquire for pulse energies.
7) Measured over 1 hour period when ambient temperature variation is less than ±2 °C.
8) Should be specified when ordering. Inquire for custom pulse repetition rates.
9) Gaussian fit >80%.
10) Full angle measured at the 1/e2 level at 1064 nm .
11) Beam diameter is measured at 1064 nm at the 1/e2 level.
12) RMS value measured from 300 shots.
13) Required current rating can be calculated by dividing power rating by mains voltage.
Option P30 provides 30±3 ps output pulse duration. Inquire for pulse energy specifications. | 
公司新闻
